The quick answer is yes. A check value on your pool heater is advantageous to your system. Check valves, which keep water moving through the pump and filter even when the device is switched off, allow in-ground pool pumps to catch prime more quickly.
In a number of water features, check valves also serve an essential purpose and are therefore essential components. It is possible that the problem is with the check valve if your fountains, jets, or waterfalls are not functioning as they should be. You’ll discover that many of these features get their supply of water from a reservoir.
You’ll find that many of these features draw water from a reservoir. When the pump is turned off, just like it does in other situations, the water will begin to drain from the reservoirs. If you have a check valve that is correctly operating and leading into the reservoir, then the water level in the reservoir will be maintained by the check valve.
Where Do You Put a Check Valve on a Pool Heater?
If they are positioned in a location where they are too close to other pieces of equipment, pool chlorinators pose a risk of causing harm to the pool’s heater or filter.
A check valve can be installed immediately before an in-line chlorinator or just before an off-line chlorinator’s injection point. This will prevent excessive amounts of chlorine from leaking backwards into heaters, filters, or other pool equipment.
To check the current price and availability of a Pool Heater Check Valve, click here to view a listing on Amazon.
Why Do You Need a Check Valve on a Pool Heater?
A check valve is a one-way flow valve with the function of preventing water from cycling in solar systems or bypass loops by restricting the flow of water in the opposite direction or preventing it from flowing backwards.
In the plumbing of swimming pools, spas, and fountains, check valves are fitted so that water may only flow in one way at a time. This prevents any backflow from occurring.
When Should I Use My Pool Check Valve?
Pipelines typically have check valves built in them to prevent backflow from occurring. A check valve is essentially the same thing as a one-way valve, with the exception that the flow can run freely in only one direction; nevertheless, the valve will shut off to safeguard the piping, other valves, pumps, and so on if the flow reverses.
When the pump is turned off, a check valve in the pool’s circulation system guarantees that the water does not divert from its regular route and flow backward due to gravity. They protect the pool’s piping from decaying and the water from being polluted with mud and debris.
These valves are also referred to as one-way and non-return valves. The type of pool equipment installed will have a considerable impact on the number of check valves required.
If the pool is heated by solar panels, a check valve should be installed before the chlorination equipment, in the pipe going up to the solar panels, and for water features that take water from a source other than the pool.
Does a Pool Heater Need a Bypass Valve?
The operation of a pool heater may rack up large expenditures, particularly when it is used continually. This is especially true when the heater is left on for an extended period of time.
It is conceivable that the heater on a residential pool will be utilized on occasion; however, on the whole, it is not likely that the heater will be in use for an extended stretch of time without a break.
Every time the heater is used or every time the water in the pool is heated to the desired temperature, it is not always essential to adjust the settings on the bypass valve. It is acceptable for water to go through the heater in a nonstop cycle as long as it is not happening for any of the following reasons:
Shocking the pool In the event that algae grows in the pool or the water turns green, adding chemicals to the water to remove the algae will cause the water to become corrosive. Put the heater on hold until the pool has been cleaned.
Bypass Valves are Important for Winter Time
When closing down a pool for the winter in an area with a cold environment, the valves should be set to bypass. This is part of the winterization process.
This not only ensures that the pump will prime quickly, improving the life of the motor, but it also prevents DE or dirt from returning to the pool when the pump is turned off. A check valve is a basic piece of machinery that may save you from a lot of trouble.
When the heater is used infrequently or not at all, which is often the case, it should be turned off and bypassed. There should NEVER be any water going through a heater that is either faulty or not functioning properly.
Chemistry that is out of balance the water’s chemistry should be as close to perfect as is practically possible. When only a little number of chemicals need to be added to the water on a daily or weekly basis for maintenance, there is no need to go around the heater.
When Utilizing Algaecides. Many of the solutions available for controlling algae contain copper. If you don’t have a heater, you can use this instead. It’s fine. In the event that an algaecide is applied, one that does not include copper is recommended.
Final Thoughts
The incorporation of a check value for the pool heater that you own will be helpful to your system in the long run. Above-ground pool pumps that have check valves installed are able to reach prime (full pressure) in a more expeditious way than pumps without these devices.
In addition, check valves are a key component because of the role they perform, which allows them to fulfill a significant purpose.
If the fountains, jets, or waterfalls in your pool are not performing as they should be, the check valve may be the source of the issue.